Browse Our Site

 

Almost everyone seems to have their own way of thinking about How to Install a Shower Drain.

Upgrading a bathroom is one of the a lot more popular residence improvement jobs. Handling the plumbing for draining your shower can be exceedingly simple unless you overdo it.

 

 

Managing Your Own Shower Drainpipe Installation Project

Whether you are a tub or shower individual, most people try to find shower just options when purchasing a house. This straightforward fact indicates more than a few house owners invest a weekend break updating or installing showers in their restrooms. Luckily for you, it is a rather simple process.

A collection agency or frying pan describes the straight surface area located at the bottom of the shower. The collection agency usually includes a non-slip surface area a little banked in the direction of the facility or any place the drainpipe lies. Incorporated with 3 to four inch walls around the side, the goal of your shower water drainage plumbing is to obtain the water to move to and also down the drain.

You can physically build a collector for your new shower, but you really need to think about it. Do you really want to enter into the problems of obtaining the sloping right, as well as making certain every element of it is water resistant? As well as I imply every aspect! It is much easier to simply acquire a pre-cast enthusiast online or at your neighborhood Lowes, House Depot or hardware store. Building one may sound like an excellent concept, but you will probably really feel in different ways after a number of hours.

Regardless of just how you set about getting a pan, you need to strive to use one that has the drainpipe situated in the same spot as the initial pan. Moving the drain pipelines can be a task, particularly if the building contractor made use of a distinct framing framework. If you are figured out to move the drainpipe, you are mosting likely to have to cut down the pipe or extend it, which may suggest destroying large portions of the floor. Rephrase, you are mosting likely to be taking a look at a several weekend break job.

Assuming we have our drainpipe lined up, the real connect is fairly basic. The drainage pipeline ought to be encountering vertical approximately the collection agency. It will certainly commonly look like a "U", which indicates it serves as a cleanout to maintain nasty smells from returning up from the drain. To attach the drain, you are mosting likely to create a water limited link between a drainpipe cap on the top of the pan and the drainage pipeline. Systems differ, yet you are usually mosting likely to do this by placing a combining piece on the top of the drain pipeline. This is then covered with gaskets and also literally screwed into the drain cap. The drain cap need to serve as a locknut, to wit, it screws straight onto the combining.

The challenging part of this procedure is obtaining your drain cap to suit a water tight position in the pan. This is completed by withdrawing the drain cap when you are sure whatever meshes. Then, you put plumbing professionals putty around the bottom of the cap and then screw it back on. The putty ought to develop a limited seal in between the cap and the shower pan, which keeps water from dripping under it and also right into the framing under the shower.

Undoubtedly, washroom showers come in a wide variety of styles these days. If you purchase a collector, they often included plumbing guidelines or the shop can keep in mind anything uncommon you should know. It seems intricate, however is commonly pretty easy. Have fun!

 

How To Install & Replace A Shower Drain In 5 Steps

 

Replacing a shower drain, or installing one for the first time, often requires a plumber, but if you’re confident in your DIY skills then you may be able to do it yourself. Your new shower drain should come with specific installation instructions, so take time to familiarise yourself with those before you get started. There are several types of shower drain, and the one you choose or are supplied with will depend on your shower tray, your pipes and the manufacturer’s recommendations. All Mira shower trays are compatible with compression-style shower drains, which attach to your home’s drainpipes with compression washers and nuts. Here’s an overview of how to install this type of drain.

 

How to install a compression-style drain

 

Please bear in mind that these are general instructions, and you should refer to the manufacturer’s recommendations to install your shower drain.

 

Trim the drainpipe

 

The drainpipe should come up to 2cm below the lip of the shower drain. You might need to lift the shower base on to mark the right height, and then remove it again before trimming the drainpipe with a hacksaw. Ensure the cut is flat and level.

 

Attach the drain assembly to the shower base

 

Apply silicone caulk to the lower rim of the drain assembly and insert it into the shower base from the top side of the base. This should be done before the base is put in place on the floor. Press the drain assembly firmly into place so that the caulk forms an even seal.

Slide the rubber washer and slip washer on to the drain assembly from underneath the shower base, then thread the drain nut on and tighten it with pliers.

Wipe away any excess caulk that has oozed out.

 

Put the shower base in position

 

Carefully position the shower base so that the drain assembly lines up with the drainpipe and fits inside it. It’s a good idea to get someone else to help out, and it’s usually easier to set the back of the base down first, and then lower the front of the base down.

 

Insert the compression gasket and nut

 

Slide the rubber compression gasket down into the drain opening so that it fits around the drainpipe. The top of the gasket should line up with the top of the pipe, or be slightly lower.

Drop the compression nut into the drain opening and use the fitting tool that will likely have been provided and a screwdriver to tighten the nut. As you tighten it, the gasket will be compressed against the drainpipe, creating a watertight seal.

 

Fit the metal strainer

 

Press the metal strainer into the drain opening, making sure the top surface is lower than the shower floor around it.

And there you have it, a brand-new shower drain! Allow the silicone to set for a full 24 hours before using the shower.

 

Cleaning and maintenance of your shower drain

 

Shower drains can quickly become clogged with hair and a build-up of product, which can lead to bad smells and can prevent your shower water from draining efficiently.

To maintain your shower drain, clear out any strands of hair that gather on the metal strainer after each shower. We recommend cleaning your shower drain thoroughly once a month using boiling water to loosen up soap scum and get things moving.

https://www.mirashowers.co.uk/blog/how-to/how-to-install-replace-a-shower-drain-in-5-steps/

 

I am very excited about How to Choose the Best Drain for Your Shower and I am assuming you appreciated my page. Sharing is good. Helping people is fun. I enjoy reading our article about Easy Shower Drain Installation Tips.